ANSI C37.90 (Total Compliance):
(UL Required)

• Make and Carry Ratings Sec. 6.7
• Temperature Test Sec. 7
• Dielectric Test Sec. 8
• Surge Withstand Test Sec. 9

UL 1053 (UL Required):

• Current Withstand Test Sec. 27
• Control Power Test Sec. 18
• Output Test Sec. 19
• Temperature Test Sec. 20
• Calibration of Ground Element Sec. 21
• Overvoltage Sec. 22
• Overload Sec. 23
• Endurance - Verify with Calibration Tests Sec. 24
• Dielectric Voltage Withstand Test Sec. 25

CURRENT INPUTS:

• CT's - 5 Amp Secondary
• CT Burden
  <0.004Ohm
  <0.1VA@Rated Current(5A)
• In - 5A(Secondary) or CT(Primary)
• Saturation - 30 x In
• Momentary - 100 x In for 1 Second

CT(Primary) SETTINGS AVAILABLE:

• Phase and Ground:
  5/10/25/50/75/100/150/200/250/300/400/500/600/630
  800/1000/1200/1250/1500/1600/2000/2400/2500
  3000/3200/4000/5000

ZONE SELECTIVE INTERLOCKS:

• Phase - Inverse Time Overcurrent and Short Delay
• Ground - Inverse Time Overcurrent and Short Delay

CONTROL POWER:

• Input Voltage
  Nominal 48 to 250VDC
  Nominal 120 TO 240vac 50/60Hz
• Input Voltage
  Operating Range 28 to 280VDC
  Operating Range 90 TO 254vac 50/60Hz
• Power Consumption- 25VA

OUTPUT TRIP CONTACTS:

• Trip OC/Communication [Time Delay]
  - Make 30 Amps for 0.25 Seconds
  - 0.25 Amp Break at 250VDC
• Trip Instantaneous
  - 5 Amp Break at 120/240VAC
• Communications Close
  - Meets ANSI C37.90, Paragraph 6.7

ENVIRONMENT:

• Operating Temperature: -30 to +55 Degrees C
• Operating Humidity: 0 to 95% Relative Humidity [Non-Condensing]
• Storage Temperature: -40 to +70 Degrees C

AUXILIARY ALARM CONTACTS:

• Protection Off Alarm - 5 Amp Continuous
• Trip Alarm - 5 Amp Break at 120/240VAC

TESTS:

• Dielectric Strength
  Current Inputs - 3000VAC for 1 Minute Phase-Phase
• Seismic Test
  Meets requirements for UBC and California Building Code Zone 4. ZPA=3.5

ADDITIONAL TESTS (UL REQUIRED):

• Hot and Cold Calibration of Phase Elements
• Meter Readout Accuracy
• Zone Interlocking Functionality

EMC TESTS:

• IEC 255-22-2, Electrostatic Discharge Test (ESD), Rating of 8kV
• IEC 255-22-3, (ENV50140), Radiated RF Immunity
• ENV 50141, Conducted RF Immunity
• CISPR 11 Class A
• CFR 47 FCC Part 15 Subpart b Class A

PHASE AND GROUND TIME-CURRENT CURVES:

• Low Voltage Breaker
  It - Moderately Inverse
  I2t - Very Inverse
  I4t - Extremely Inverse
  FLAT - Definite Time
  
• ANSI(Per ANSI C37.112, 1996)
  Moderately Inverse
  Extremely Inverse
• IEC (Per IEC 255-3, 1989)
  IEC-A - Moderately Inverse IEC-B - Very Inverse IEC-C - Extremely Inverse IEC-D - Definit Time

PHASE OVERCURRENT PICKUP RANGES:

• Inverse Time Overcurrent
  Setting: (0.2 to 2.2) x In (28 Settings)
• Short Delay Setting
  (1 to 11) x In, None[25 Settings]
• Instantaneous Setting
  (1 to 25) x In, None[30 Settings]

GROUND OVERCURRENT PICKUP RANGES:

• Inverse Time Overcurrent
  Setting: (0.1 to 2.2) x In None[26 Settings]
• Short Delay Setting
  (0.1 to 11) x In, None[45 Settings]
• Instantaneous Setting
  (0.5 to 11) x In, None[33 Settings]

TIME DELAY SETTINGS:

• Inverse Time Overcurrent
  Time Multiplier: It, I2t, I4t Curve: 0.2 to 40 [47 Settings]
  FLAT: 0.2 to 2 [21 Settings]
  ANSI(all): 0.1 to 5.0 [50 Settings]
  IEC(all): 0.05 to 1.00 [20 Settings]
  
• Short Delay Time
  0.05 to 1.5 Sec. [22 Settings]

CURRENT MONITORING:

• True RMS Sensing
  3-Phase and Ground
• Display Accuracy
  +/- 1% of Full Scale[In] from 0.04xIn to 1xIn
  +/- 2% of Full Scale[In] from 1xIn to 2xIn
• Amp Demand
  Average Demand over 5 Minute Sampling Window
• High Load
  85% of Inverse Time Overcurrent Setting

TIMING ACCURACY:

• Inverse Time Overcurrent
  Time - +/- 10% at >1.25 x Pickup
• Short Delay Time
  +/- 50ms

COMMUNICATIONS:

• IMPACC Compatible
• Baud Rate - 1200 or 9600
• Catalog DT3000 has Built-in INCOM, NO PONI REQUIRED!